E-Station (BC6-DC) BC6-DC Charger
[BC6-DC]

Balance board Not Included

Align/Esky/hobby hangar  JST XH

Specification
Operating voltage	DC 11~18 volts
Idling current	approx. 100mA
Charge/discharge power	max. 80/8W
NiCd/MH	1~15 cells
LiIo/LiPo/LiFe	1~6 series
Pb	2~20V
Charge current	0.1 to 5.0A
Discharg current	0.1 to 1.0A
No. of cycle	1 to 5 times
Battery data memory	up to 5 data
Weight	340g
Dimension	130x90x30 mm

User's setting-up parameters
Lithium battery voltage type	LiIo:3.6V, LiPo:3.7V, LiFe:3.3V
NiCd Delta-peak voltage sensitivity	5 to 20mV
NiMH Delta-peak voltage sensitivity	5 to 20mV
Battery temperature cut-off	20 to 80C or OFF
Waste time between charge/discharge	1 to 60 min.
Trickle charge mode	ON/OFF, up to 200mA
Integral timer limit for safety	10 to 720 min.or OFF
Maximum charging capacity limit for safety	10 to 9990mAh or OFF
Key beep and buzzer sound	ON/OFF
Input power low alert	10 to 11V
LCD back-light brightness	1 to 100 steps

Operating software

   Every operating program in the unit is controlled with mutual links and communications to prevent every possible error, so it introduces the maximum safety, such as input voltage warning, reverse polarity protection and Lithium cell-count input error warning.

-  Individual voltage balancer for Lithium batteries

   BC6-DC has an individual cell voltage balancer inside. So it does not need any balancer separately when charging Lithium batteries (LiIo/LiPo/LiFe) for voltage balancing.

-  Accept various types of Lithium battery

  BC6-DC can accept three types of Lithium batteries - LiIo, LiPo and LiFe. They have different characteristics by their chemistry. You can select any one of them that you are going to process before the job. For their specifications, refer 'Warnings and safety notes' section.

- Lithium battery 'Fast' and 'Storage' mode

   You can charge Lithium battery for special purposes. 'Fast' charge reduces the charging time of Lithium battery and 'Storage' mode controls the final voltage of the battery to be suit for long time storage.

- Maximum safety 

    Delta-peak sensitivity : The automatic charge termination program works on the principle of the Delta-peak voltage detection. (NiCd/NiMH)

    Auto-charge current limit : When charging NiCd or NiMH at 'AUTO' current mode, you can set the upper limit of charge current to avoid from feeding high current to the battery. This is very useful when charging the low impedance and small capacity NiMH battery in 'AUTO' mode.

   Capacity limit : The charging capacity always calculated by multiple of the charging current and time. If the charging capacity exceeds the limit the process will be terminated automatically when you set the maximum value.

-  Data store/load 

   For users convenience it can store maximum 10 data of different batteries. You can establish the data contains program setting of the battery to charge or discharge continually. These data can be called out at any time you need and the process can be executed without program setting.

-  Cyclic charging/discharging 

   Perform 1 to 5 cycles of charge>discharge or discharge>charge continually for battery refreshing and balancing.

-  PC based analysis using USB communication 

   For technical expert, BC6-10 offers PC based program can analysis the characteristic of the battery by USB port. It shows a graph of voltage, current, capacity and temperature curves. It also shows the individual voltage of each cell in the Lithium battery pack.

- Robust outer aluminum case 

  High-quality aluminum case is durable and very efficient to cool out the internal heat

Accessories
EAC110	Temperature sensor cable	Optional
EAC117	4mm gold banana plug with silicon cable and alligator clips	Standard
EAC300	Program kit for PC (CD + USB cable)	Optional
EAC12X	Balance adaptor board for Lixx	Optional